The effects of high salinity on nitrogen removal and the formation characteristics of aerobic granular sludge

Article information

Environmental Engineering Research. 2020;25(5):659-667
Publication date (electronic) : 2019 September 16
doi : https://doi.org/10.4491/eer.2019.233
1BlueBank Co., Ltd., Business Incubator Center, Myongji University, Yongin 17058, Republic of Korea
2Department of Environmental Engineering and Energy, Myongji University, Yongin 17058, Republic of Korea
Corresponding author: Email: dhahn@mju.ac.kr, Tel: +82-31-321-5901, Fax: +82-505-300-5901
Received 2019 June 03; Accepted 2019 September 09.

Abstract

This study investigated the biological treatment of high-salinity wastewater using aerobic granular sludge (AGS). The removal performance, AGS characteristics, and microbial community were examined under salinity conditions ranging from 0.5 to 3.0 wt.%. When the salinity was increased, the removal efficiency of the chemical oxygen demand did not change substantially. The mean removal efficiency of NH4+-N ranged from 43.7 to 72.6% during the operation period. As for the concentration of extracellular polymeric substances (EPS), the polysaccharide/protein (PS/PN) ratio increased from 0.37 to 0.57. The concentrations of the mixed liquor suspended solid (MLSS) and mixed liquor volatile suspended solid (MLVSS) were 4,560 and 3,170 mg/L, respectively, in the end phase, and the MLVSS/MLSS ratio decreased from 0.81 to 0.69. The sludge volume index (SVI30) decreased linearly from 88 to 58 mL/g. In the microbial community analysis, Nitrosomonas species accounted for 22.9% of the total bacteria in the initial phase, whereas Halomonas accounted for 43.2% in the end phase. Hence, the gradually increased salinity appears to facilitate the dominance of halophilic microorganisms in the long-term operation of an AGS-based biological treatment system and the stable retention of AGS.

1. Introduction

The intrusion of seawater caused by excessive groundwater extraction and the rising sea level due to global warming add to the volume of high-salinity wastewater flowing into the sewage treatment plants in coastal areas [13]. Furthermore, the high-salinity wastewater generated by marine aquaculture and seafood processing industries is known to be a factor impacting the efficient treatment of the contamination sources in established wastewater treatment plants [4, 5].

The current physicochemical treatment technologies for saline wastewater include capacitive deionization, membrane separation, ion exchange, and electrodialysis [610]. These processes, however, are costly and require control measures against secondary contamination; thus, they are only applicable under specific conditions. In addition, physicochemical treatment is not suitable for high-salinity wastewater due to its low removal efficiency of dissolved chemical oxygen demand (COD) and its high consumption of chemicals. By contrast, biological treatment processes are economical and avoid secondary contamination, and thus are preferred over physicochemical technologies [11, 12]. Yet, high-salinity wastewater contains an abundance of organic compounds and soluble inorganic salt, which directly or indirectly inhibits the cell division and proliferation of microorganisms in wastewater treatment plants and may ultimately be detrimental to the growth, productivity, and performance of the microorganisms [13, 14]. In particular, when highly saline wastewater is biologically treated, osmotic pressure causes the dewatering of the cell sap resulting in plasmolysis, or the contraction of the microorganism protoplast, and the decline in microbial activation [15, 16]. Thus, much attention has been paid to the biological treatment of high-salinity wastewater from the perspectives of sewerage engineering and marine environment protection. During the past several decades, diverse treatment methods and reactors have been developed to improve the efficiency of biological treatment of highly saline wastewater [1721]. However, previous studies on the contamination removal performance, e.g. the efficiency of removing organic matter and nitrogen from saline wastewater, used the general activated sludge process, and mainly involved NaCl among other salts [2225].

Lately, the aerobic granular sludge (AGS) process based on the wastewater treatment system has attracted attention due to the higher concentration of microorganisms, higher treatment efficiency, superior sedimentation, and stronger resistance to shock load compared to the activated sludge [2629]. The AGS is reported to settle more stably in sequencing batch reactors (SBRs) than in continuous flow reactors, and more regularly under highly saline conditions [30, 31].

Research on the AGS-based treatment of high-salinity wastewater largely revolves around the formation characteristics of AGS, granular stability, and microbial community analysis. That said, most studies are similar to the existing research based on the activated sludge in that they involve only NaCl, whereas diverse ionic substances in seawater have not been well studied [3234]. Hence, this study explored the characteristic biological removal of nitrogen from the AGS and the formation thereof using the SBR under the condition of gradually increased seawater salinity. This paper also discusses the efficient biological treatment of high-salinity wastewater based on the following: (i) evaluation of the removal efficiency of organic matter and nitrogen; (ii) analysis of extracellular polymeric substances (EPS) and sedimentation; and (iii) observation of the microbial surface and analysis of the microbial community.

2. Materials and Methods

2.1. Synthetic Wastewater

Synthetic saline wastewater was prepared by referring to the appearance of real seawater [3536]. During the operation period, the salinity was increased stepwise: 0.5, 1.0, 1.5, 2.0, 2.5, and 3.0 wt.% (Table 1). The influent carbon/nitrogen (C/N) ratio was set at 8 in the reactor with an influent COD and TN of 200 and 25 mg/L, respectively, during the operation period. CH3COONa and NH4Cl were used to prepare the COD and NH4+-N, respectively. KCl, NaCl, MgCl2, CaCl2, and MgSO4 (Samchun Chemical Co. Ltd., Korea) were used to prepare the salinity. The alkalinity required for nitrification was obtained by injecting 200 mg/L of NaHCO3 during the operation period.

Characteristics of Salinity Wastewater (unit: mg/L)

2.2. Reactor and Experimental Setup

As shown in Fig. 1, a laboratory-scale SBR with an effective volume of 5 L (length: 15 cm; width: 15 cm; height: 22.2 cm) was used in the experiments. A peristaltic pump was used to feed the influent into the reactor. The effluent was drawn at a height of 11.1 cm from the bottom of the reactor by a solenoid valve, and the volume exchange rate for every cycle was 50%. Air was introduced by an air diffuser at the bottom of the reactor with an aeration flow rate of 2 L/min to maintain dissolved oxygen (DO) concentration of 1.0–2.0 mg/L during the aerobic period. The SBR operation consisted of three cycles per day. Each cycle lasted 8 h, including feeding (10 min), aeration (270 min), anoxic phase (150 min), settling (10 min), decanting (10 min), and an idle period (30 min) (Table 2). The SBR cycle times were controlled using a programmable logic controller (PLC). For the evaluation of the nitrogen removal efficiency and the AGS formation characteristics under varying salinity conditions, the injection of salts was increased from 0.5 to 1.0, 1.5, 2.0, 2.5, and 3.0 wt.% in the experiment. The initial mixed liquor suspended solid (MLSS) and mixed liquor volatile suspended solid (MLVSS) in the reactor were 3,070 and 2,730 mg/L, respectively. To evaluate the nitrogen removal efficiency, a specific nitrification rate (SNR) and specific denitrification rate (SDNR) was derived in the final phase of the experiment under each condition.

Fig. 1

Schematic diagram of lab. scale reactor.

Experimental Conditions of Lab. Scale Reactor

2.3. Analytical Methods

The reactor effluent was sampled seven times a week. The water was centrifuged at 4,000 rpm for 10 min to test the COD according to the standard method (5220-B) [37]. The samples for the detection of NH4+-N, NO2-N, and NO3-N were filtered by 0.45 μm glass fiber filter and tested by the standard methods (4500-NH3-C, 4500-NO2-B, and 4500-NO3-B, respectively) [37]. The sludge physical properties included the MLSS, MLVSS, and sludge volume index (SVI30). MLSS, MLVSS, and SVI30 were measured according to the standard methods (2540-B, D, 2540-E, and 2710-D, respectively) [37]. The EPS of the granules were extracted using formaldehyde and NaOH [38]. The contents of the extracted proteins (PN) and polysaccharides (PS) were measured using Folin’s reagent [39] and phenol-vitriol colorimetry [40], respectively. The change in surface shape and the characteristics of AGS were examined using an optical microscope (CX31; Olympus Corp., Japan) and the collected sludge was covered with cover glass of 0.17 mm thickness and observed at 40x magnification.

2.4. Microbial Community

Pyrosequencing data analysis was performed to observe the microbial community. The community analysis was performed to determine the AGS characteristics of the initial phase and the difference in the end phase. Each sludge sample was homogenized (MP-80; Hanil, Korea). The homogenized sample was centrifuged to discard the supernatant, and DNA extraction was carried out in accordance with the manual provided by the manufacturer. The FastDNA Spin Kit for Soil (MP Biomedicals, Santa Ana, CA, USA) was used for DNA extraction. Polymerase chain reaction (PCR) (C1000 Touch Thermal Cycler, Bio-Rad, and Hercules, CA, USA) was performed using 1 μL of extracted DNA. The initial denaturation was performed at 95°C for 5 min. Subsequently, all procedures (denaturation at 95°C for 30 s, annealing at 55°C for 30 s, extension at 72°C for 30 s, and final extension at 72°C for 7 min) were 30 cycles each and fixed at 4°C. For PCR, the purity of the DNA was increased using the QIAquick PCR Purification Kit (Qiagen, Valencia, CA, USA). Pyrosequencing of the amplified DNA samples was conducted using a 454 GS FLX Junior Sequencing System (Roche, Branford, CT, USA). The resulting data was analyzed through the CLcommunity program (Chunlab Inc., Seoul, Korea) [41].

3. Results and Discussion

3.1. Reactor Performance

The reactor performance in terms of COD removal efficiency during the experiment is presented in Fig. 2. Based on the analysis results, the average COD removal efficiency was approximately 90% (88.9–90.5%) for the duration of the operation. Also, the concentration of the treated water was gradually reduced at the start of each condition. In addition, a gradual recovery of the removal efficiency was observed after 1–2 weeks of operation. These results may be explained by the fact that the AGS adapted to the gradual increase in salinity. The effluent COD result is always taken as an index of the metabolic activity of heterotrophic bacteria [42, 43]. In Fig. 2, the effluent COD concentration changed significantly when the influent salinity was increased from 0.5 up to 3.0 wt.%. These results indicate that the microorganisms removing the COD were not sensitive to salt stress, which agrees with previous reports [44, 45]. Taheri et al. [33] performed long-term (269 d) observation of the COD removal efficiency in AGS using the SBR process by increasing the salt concentration (NaCl) from 0.2 to 1.0%, and achieved a removal efficiency of more than 90% for the duration of the operation. The stable COD removal efficiency against the increasing salt content was attributed to the microbial organic matter removal mechanism adaptability to the salinity, which was similar to the conclusion drawn in this study. Vo et al. [46] investigated the growth dynamics of freshwater and marine microalgae with supported biochemical performance in saline wastewater and the assimilation of pollutants by a developed method. They reported that the highest total organic carbon (TOC) removal efficiency occurred at salinities of 0.1 and 1%. Typically for Chlorella vulgaris, 92% of the TOC was removed in 10 d and this corresponded to 0.1% salinity. At 1% salinity and similar hydraulic retention time (HRT), approximately 50% of the TOC was eliminated. It is considered that the achieved COD removal efficiency in this study is comparable to that in other studies. Table S1 compares the COD removal efficiency by salinity injection [33, 34, 4753].

Fig. 2

Results of COD concentration with salinity injection.

The courses of nitrogen compounds are indicated in Fig. 3. The mean removal efficiency of NH4+-N ranged from 43.7 to 72.6% for the duration of the operation. Similar to the foregoing COD result, the NH4+-N removal efficiency gradually recovered in line with the microbial acclimation, and notably, with the increase in the injected NaCl, NO2-N gradually accumulated up to 16.8 mg/L by the end of the operation [54]. Comparable to the study by Wan et al. [53], in which the NaCl was increased up to 5% in a partial nitrification of NH4+-N, this finding seems attributable to the nitrite oxidizing bacteria (NOB), which are more susceptible to the inhibitory effects of salinity than the ammonia oxidizing bacteria (AOB). The increase in salinity could induce stress in microbial species, resulting in the decrease of cellular activities and even plasmolysis [44, 55]. These changes slow down the microbial substrate utilization rate and cause the release of intracellular constituents as the salinity increases [56]. In addition, nitrite reductase is more sensitive than nitrate reductase to environment changes [57], thus leading to NO2-N accumulation. Table S2 compares the NH4+-N removal efficiency by salinity injection [19, 34, 48, 5863].

Fig. 3

Results of nitrogen compounds concentration with salinity injection.

Fig. 4 shows the SNR and SDNR values by salinity under each condition. Based on the analysis results, with the increase in the injected NaCl, the mean SNR decreased from 0.112 to 0.040 mg NH4+-N/mg MLVSS d, while the mean SDNR fell from 0.094 to 0.037 mg NO3-N/mg MLVSS d. The decreasing trend of SNR was different from the results obtained by Zhao et al. [48]. They reported that the removal efficiency of NH4+-N was not significantly affected when the salinity was lower than 20 g/L. This difference may result from the diversity of treatment process and the microbial species. Also, when abruptly exposed to the higher salinity environment, bacterial cells might remain in a state of plasmolysis, resulting in the decline of denitrifying activities [64]. Kinyage et al. [65] used the recirculating aquaculture system (RAS) biofilters to analyze the NH4+-N removal rate by radically changing the salinity. They reported that very little of the NH4+-N was removed and none of the NO2-N was removed when the salinity was increased from 0 to 3.5%. Ji et al. [62] used the NO2-N accumulating granular sludge to analyze the partial denitrification performance and microbial community formation resulting from the phased increase in salinity. They reported that when the salt injection was increased from 0% up to 1.5% in phases, the denitrification rates showed a linear decrease, which parallels the present finding. In addition, they argued that all microbial species were subject to salinity limits, beyond which their activity declined, and emphasized the need for microbial acclimation to salinity via a phased increase in salinity.

Fig. 4

Results of SNR and SDNR value with salinity injection.

Considering that the abovementioned studies differ from the present study in terms of reactor types, salt injection conditions (NaCl only), operating conditions, and sludge types, it is rather implausible to compare the findings. Nonetheless, the reported decline in microbial activity and treatment efficiency with the increase in salinity bears a close parallel to the present finding, and the derived results for SNR and SDNR appear to serve as applicable reference data and design factors conducive to designing bioreactors for AGS-based treatment of high-salinity wastewater.

3.2. Extracellular Polymeric Substance

The EPS, which includes both bound and soluble polymers [66, 67], could improve the hydrophobicity and polymeric interactions, as well as create bridges between the cells and cages to entrap cells [68]. EPS also had merits in the maintenance of the microorganisms under various environments, protecting them from harm [69]. PS usually acts as the main cross-network structure as well as an adhesive to trap and collect bacteria in the AGS [70, 71]. In addition, PN can reduce the electrostatic repulsion between bacteria and increase the aggregation of AGS by enhancing the surface hydrophobicity [72].

Fig. 5 shows the PN and PS content, and the PS/PN ratio of AGS under each salinity condition. With varying levels of salinity concentration, the total EPS increased from 107 to 132 mg/g MLVSS. These results could be explained by the protective response of the AGS to salt toxicity. EPS are metabolic products that accumulate on the surface of bacterial cells, and are considered important constituents of sludge floc, providing a protective barrier against the effects of toxic chemicals [69]. Thus, the response of the bacteria in AGS to higher increments of salinity concentration is to secrete more EPS. The PN and PS compositions varied with the salinity concentration. With the injected salinity levels ranging from 0.5 to 3.0 wt.%, PN increased marginally from 78 to 84 mg/g MLVSS, whereas PS increased substantially from 29 to 48 mg/g MLVSS. Consequently, the PS/PN ratio rose from 0.37 to 0.57. Reported as a primary factor for the AGS formation, the EPS result parallels the results obtained by Mesdaghinia et al. [73] and Fang et al. [74], who attributed the change in EPS composition to the rising salinity conditions stimulating the PS release from the AGS. Guo et al. [75] investigated the effect of salinity on MBR performance and also found that the salinity shock caused a higher influence ion PS than on PN with a salinity concentration of 0.75% and 1.5% NaCl; the changes to PS in EPS were considered to be closely correlated with certain saline-resistance genera. Also, Kim et al. [76] investigated the effects of the calcium ions in reverse osmosis (RO) concentrates on biological nitrogen removal and adsorption. They reported that depending on the injected concentration of calcium ions, the adsorption of calcium ions onto the negatively charged microbial surface boosted the production of PS, which increased the intercellular adhesion, played an important role in microbial flocculation, facilitated the AGS formation, and contributed to the growth of granules. Table S3 compares the EPS secreted efficiency by salinity injection [34, 7782].

Fig. 5

Results of PN, PS and PS/PN ratio value with salinity injection.

3.3. MLSS and SVI30

Fig. S1 shows the behavior of MLSS and MLVSS by condition. Fig. S2 illustrates SVI30. Initially, the MLSS and MLVSS concentrations were 3,070 and 2,730 mg/L, respectively. In tandem with the increase in the injected salinity concentration up to 3.0 wt.%, the MLSS and MLVSS concentrations gradually increased up to 4,560 and 3,170 mg/L, respectively, by the end of the operation. That is, MLVSS did not change substantially compared with MLSS. Thus, the percentage of MLVSS in the entire MLSS (MLVSS/MLSS ratio) was 0.81 initially, which decreased to 0.69 by the end of the operation (3.0 wt.% salinity). Salinity varying from 0.5 to 3.0 wt.% exerted a positive influence on the biomass growth rate. A greater volume of inorganic materials accumulated in the granules under higher salinity conditions, resulting in a higher MLSS concentration in the reactor [83, 84].

Park and Lee [85] investigated the denitrification reaction of acid pickling wastewater containing a high concentration of NO3-N by injecting calcium ions, and reported that the MLVSS/MLSS ratio, which was 0.74 before the calcium ion injection, decreased to 0.69 following the injection of 1,000 mg/L calcium ions. They explicated that the specific gravity of the sludge increased due to the incremental injection of calcium ions adsorbed onto the microbial surface. They also reported that the adsorbed calcium ions underwent denitrification and bonded with OH ions to form CaOH2 sedimentation, which contributed to the increase in the specific gravity of the sludge. Similarly, in this study, the higher the injected NaCl, the lower the MLVSS/MLSS ratio, and the increase in the specific gravity of the sludge seems attributable to the bonding with the cations contained in the salt. In biological wastewater treatment systems, part of the produced sludge (excess sludge) must be extracted and disposed of in a safe, cost-effective manner. In addition, the handling of excess sludge is a primary concern in biological wastewater treatment. Consequently, further study on the treatment and management of excess sludge is needed in the biological treatment of high-salinity wastewater.

As for SVI30, contrary to the expectation that the increase in the NaCl would lead to an increase in osmotic pressure and microbial deflocculation, which would result in sludge with poor settling characteristics, the analysis results indicated the gradual improvement in sedimentation. With the increasing NaCl levels, the SVI30 decreased linearly from 88 to 58 mL/g, indicative of a very good sedimentation of sludge. These results could be explained as follows: inorganic materials accumulated inside the AGS, which increased the density of the AGS. As the density is defined as the mass per volume AGS, the density is increased by the salinity, which in turn affects the settling velocity [32]. This finding may also be explained by the aforementioned increase in the MLSS, and by the selection pressure operating strategy, where a short sedimentation time (10 min) was maintained to accelerate the microbial aggregation and to continuously discharge sludge with poor settling characteristics [8688].

3.4 Microscopic Observation of AGS

Fig. S3 shows the microorganisms observed with an optical microscope under varying conditions. As the abovementioned analysis results for MLSS and SVI30, microbial deflocculation was not observed for the duration of the operation, while clear forms of sludge were intuitively observed as the salinity increased. Also, the AGS, which initially measured 0.2 mm, grew to approximately 0.8–1.0 mm as the MLSS increased. This finding is consistent with Li et al. [84], who reported that the salt contained in seawater facilitated the EPS of microorganisms, increased the density and aggregation, and thus accelerated the general microbial AGS formation. In addition, observing the formation of marine microbial granular sludge under varying conditions of solid retention time (SRT) and salinity, Corsino et al. [81] reported that the injection of 40 g of NaCl/L yielded approximately 4 mm of granular sludge on average. Ou et al. [78] increased the salinity in phases from 0% to 9.0%, observed the density of wastewater rising in line with the salinity with only large-sized sludge remaining in the reactor, and considered the high salinity a principal variable inducing the formation of AGS. Thus, it is considered that modification in cell morphology such as aggregation and elongation and the cytoplasm volume, under various salinity conditions is a familiar response of certain bacteria [33].

To sum up the foregoing findings, high salinity leads to the formation of AGS, which suggests that a dominance of microorganisms adapted to salt will maintain a stable granular sludge under varying salinity levels in the long-term operation of a biological treatment system.

3.5 Microbial Communities of AGS

Fig. S4 shows the richness of microbial species for the AGS prior to and at the end of the experiment based on the pyrosequencing results, and the relationships between the total valid reads and the operational taxonomic units (OTUs). The OTUs of the samples in the initial and final phases were 1,112 and 853, respectively, indicating that the microbial species are less diverse in the final phase. This finding may be ascribable to the dominance of microbial species adapted to the gradually increasing salinity injected into the AGS. Fig. 6 shows the pyrosequencing result of the analysis of microbial communities in the initial-phase (prior to experiment) and the end-phase AGS using the dynamic pie chart (krona). The groups of initial-phase AGS and end-phase AGS differ from each other. Proteobacteria in the initial- and end-phase AGS under phylum conditions accounted for the highest percentages (65.6 and 59.2%, respectively) [41]. Also, Bacteroidetes accounted for 17.2 and 26.5%, respectively, indicating a slight increase in the final phase. The dominance rates of Bacteroidetes and Firmicutes are reported to rise under high-salinity conditions, which parallel the present findings [24, 81, 89, 90].

Fig. 6

Results of microbial communities using dynamic pie chart (Krona). (a) Initial phase AGS and (b) End phase AGS.

Under the genus condition, Nitrosomonas accounted for 22.9% in the initial phase while the halophilic (salt-tolerating) Halomonas was dominant in the final phase, accounting for 43.2% (Fig. S5). Nitrosomonas relevant to nitrification was hardly observed in the final phase with Halomonas being dominant, which seems to explain the present finding that the nitrification efficiency declined with the increase in the injected NaCl. From the perspective of microbial functional groups, the existence of halophilic or halotolerant bacteria facilitated the adaption of AGS to a saline environment. Moreover, the saline conditions stimulated the bacteria to produce more EPS to protect themselves from an adverse environment. With the increase in salinity step by step, an AGS system dominated by moderately halophilic genera was gradually formed with an increasing relative abundance of Halomonas. Moreover, Halomonas is a member of the family Halomonadaceae, which shows remarkable versatility with respect to salt tolerance [91]. Also, Wang et al. [34] reported that Halomonas was found under 7–8% salinity conditions, and that optimal growth was viable when the maximum salinity was 10% and NO3-N was used as the electron acceptor [92], which is similar to the results in the present study excluding a slight difference in the rates of microbial communities.

4. Conclusions

This study investigated the characteristic biological removal of nitrogen and the formation of AGS under the gradually increased seawater salinity conditions in a SBR. Overall, the removal efficiency of COD and NH4+-N by salinity injection showed a tendency to gradually stabilize as the AGS adapted to the salinity. The stable COD removal efficiency against the increasing salt content was attributed to the microbial organic matter removal mechanism adaptability to the salinity. Similar to the foregoing COD result, the NH4+-N removal efficiency gradually recovered in line with the microbial acclimation, and notably, with the increase in the injected NaCl. Moreover, the increased salinity conditions stimulated the release of PS from the AGS, which contributed to the formation of AGS. In the microbial community analysis, under the genus condition, Nitrosomonas accounted for 22.9% in the initial phase, whereas the halophilic Halomonas was dominant, accounting for 43.2% in the final phase. Hence, the gradually increased salinity appears to facilitate the dominance of halophilic microorganisms (Halomonas) in the long-term operation of an AGS-based biological treatment system and the stable retention of AGS, which warrants further study using real seawater.

Supplementary Information

Acknowledgements

This subject is supported by Korea Ministry of Environment as “Global Top Project” (Project No.:2016002190006).

Notes

Author Contributions

H.G.K. (Ph.D.) conducted all the experiments. D.H.A (Professor) wrote the manuscript.

References

1. Tam VT, Batelaan O, Le TT, Nhan PQ. Three-dimensional hydrostratigraphical modelling to support evaluation of recharge and saltwater intrusion in a coastal groundwater system in Vietnam. Hydrogeol J 2014;22:1749–1762.
2. Zhu L, Gong H, Li X, et al. Land subsidence due to groundwater withdrawal in the northern Beijing plain, China. Eng Geol 2015;193:243–255.
3. Wen X, Lu J, Wu J, Lin Y, Luo Y. Influence of coastal groundwater salinization on the distribution and risks of heavy metals. Sci Total Environ 2019;652:267–277.
4. Ismail SB, Jeison GD, van Lier JB. Effects of high salinity wastewater on methanogenic sludge bed systems. Water Sci Technol 2008;58:1963–1970.
5. Guo N, Wang Y, Tong T, Wang S. The fate of antibiotic resistance genes and their potential hosts during bio-electrochemical treatment of high-salinity pharmaceutical wastewater. Water Res 2018;133:79–86.
6. Huang X, Yang J, Wang J, Bi J, Xie C, Hao H. Design and synthesis of core-shell Fe3O4@PTMT composite magnetic microspheres for adsorption of heavy metals from high salinity wastewater. Chemosphere 2018;206:513–521.
7. Wen J, Dong H, Zeng G. Application of zeolite in removing salinity/sodicity from wastewater: A review of mechanisms, challenges and opportunities. J Clean Prod 2018;197:1435–1446.
8. Peng X, Zheng D, Xu H. The feasibility and mechanism of reverse electrodialysis enhanced photocatalytic fuel cell-Fenton system on advanced treatment of coal gasification wastewater. Sep Purif Technol 2019;220:183–188.
9. Rae IB, Pap S, Svobodova D, Gibb SW. Comparison of sustainable biosorbents and ion-exchange resins to remove Sr2+ from simulant nuclear wastewater: Batch, dynamic and mechanism studies. Sci Total Environ 2019;650:2411–2422.
10. Tan X, Acquah I, Liu H, Li W, Tan S. A critical review on saline wastewater treatment by membrane bioreactor (MBR) from a microbial perspective. Chemosphere 2019;220:1150–1162.
11. Liang Y, Zhu H, Bañuelos G, et al. Constructed wetlands for saline wastewater treatment: A review. Ecol Eng 2017;98:275–285.
12. Ahn YH, Lee JW, Kim HC, Kwon SY. Lithoautotrophic nitrogen removal with anaerobic granular sludge as seed biomass and its microbial community. Environ Eng Res 2006;11:173–180.
13. O’Neill FJ, Bromley-Challenor KCA, Greenwood RJ, Knapp JS. Bacterial growth on aniline: implications for the biotreatment of industrial wastewater. Water Res 2000;34:4397–4409.
14. Oie CSI, Albaugh CE, Peyton BM. Benzoate and salicylate degradation by Halomonas campisalis, an alkaliphilic and moderately halophilic microorganism. Water Res 2007;41:1235–1242.
15. Rivadeneyra MA, Martin-Algarra A, Sanchez-Navas A, Martin-Ramos D. Carbonate and phosphate precipitation by Chromohalobacter marismortui. Geomicrobiol J 2006;23:89–101.
16. van den Bogaart G, Hermans N, Krasnikov V, Poolman B. Protein mobility and diffusive barriers in Escherichia coli: consequences of osmotic stress. Mol Microbiol 2007;64:858–871.
17. Khengaoui K, Mahammed MH, Touil Y, Amrane A. Influence of Secondary Salinity Wastewater on the Efficiency of Biological Treatment of Sand Filter. Energy Procedia 2015;74:398–403.
18. Liu M, Li Q, Sun H, et al. Impact of salinity on antibiotic resistance genes in wastewater treatment bioreactors. Chem Eng J 2018;338:557–563.
19. Chen X, Wang X, Chen X, et al. Salt inhibition on partial nitritation performance of ammonium-rich saline wastewater in the zeolite biological aerated filter. Bioresour Technol 2019;280:287–294.
20. Zhang Y, Kuroda M, Arai S, Kato F, Inoue D, Lke M. Biological treatment of selenate-containing saline wastewater by activated sludge under oxygen-limiting conditions. Water Res 2019;154:327–335.
21. Moon BH, Park KH, Kim SS, Yoon CH. Effects of aerobic and non-aerobic starvation on SBR performance when treating saline wastewater. Environ Eng Res 2012;17:139–144.
22. Zhang Y, Li B, Xu R-X, Wang G-X, Zhou Y, Xie B. Effects of pressurized aeration on organic degradation efficiency and bacterial community structure of activated sludge treating saline wastewater. Bioresour Technol 2016;222:182–189.
23. Tan S, Cui C, Hou Y, et al. Cultivation of activated sludge using sea mud as seed to treat industrial phenolic wastewater with high salinity. Mar Pollut Bull 2017;114:867–870.
24. He H, Chen Y, Li X, Cheng Y, Yang C, Zeng G. Influence of salinity on microorganisms in activated sludge processes: A review. Int Biodeterior Biodegrad 2017;119:520–527.
25. Hu Y-Q, Wei W, Gao M, Zhou Y, Wang G-X, Zhang Y. Effect of pure oxygen aeration on extracellular polymeric substances (EPS) of activated sludge treating saline wastewater. Process Saf Environ Prot 2019;123:344–350.
26. Chen C, Ming J, Yoza BA, et al. Characterization of aerobic granular sludge used for the treatment of petroleum wastewater. Bioresour Technol 2019;271:353–359.
27. Wang X-C, Chen Z-L, Kang J, Zhao X, Shen J-M, Yang L. The key role of inoculated sludge in fast start-up of sequencing batch reactor for the domestication of aerobic granular sludge. J Environ Sci 2019;78:127–136.
28. Yin Y, Sun J, Liu F, Wang L. Effect of nitrogen deficiency on the stability of aerobic granular sludge. Bioresour Technol 2019;275:307–313.
29. Lee HL, Ryu JH, Lee YP, et al. Aerobic granules for the effective oxidation of ammonium nitrogen. Environ Eng Res 2014;19:23–29.
30. Jung Y-C, Adav SS, Lee D-J, Tay J-H. Stable aerobic granules for continuous-flow reactors: Precipitating calcium and iron salts in granular interiors. Bioresour Technol 2010;101:8051–8057.
31. Hao T, Wei L, Lu H, et al. Characterization of sulfate-reducing granular sludge in the SANI® process. Water Res 2013;47:7042–7052.
32. Winkler MK-H, Bassin JP, Kleerebezem R, van der Lans RGJM, van Loosdrecht MCM. Temperature and salt effects on settling velocity in granular sludge technology. Water Res 2012;46:5445–5451.
33. Taheri E, Hajian MHK, Amin MM, Nikaeen M, Hassanzadeh A. Treatment of saline wastewater by a sequencing batch reactor with emphasis on aerobic granule formation. Bioresour Technol 2012;111:21–26.
34. Wang Z, Gao M, She Z. Effects of salinity on performance, extracellular polymeric substances and microbial community of an aerobic granular sequencing batch reactor. Sep Purif Technol 2015;144:223–231.
35. Shih Y-J, Hsia K-F, Chen C-W, Chen C-F, Dong C-D. Characteristics of trichloroethene (TCE) dechlorination in seawater over a granulated zero-valent iron. Chemosphere 2019;216:40–47.
36. Ahunbay MG. Achieving high water recovery at low pressure in reverse osmosis processes for seawater desalination. Desalination 2019;465:58–68.
37. APHA (American Public Health Association). Standard methods for the examination of water and wastewater Washington D.C: APHA; 2005.
38. Liu H, Fang HHP. Extraction of extracellular polymeric substances (EPS) of sludges. J Biotechnol 2002;95:249–256.
39. Lowry OH, Rosebrough NJ, Farr AL, Randall RJ. Protein measurement with the Folin phenol reagent. J Biol Chem 1951;193:265–275.
40. Herbert D, Philipps PJ, Strange RE. Carbohydrate analysis. Methods Enzymol B 1971;5:265–277.
41. Yae JB, Ryu JH, Tuyen NV, Kim HG, Hong SW, Ahn DH. An aerobic granular sludge process for treating low carbon/nitrogen ratio sewage. Environ Eng Res 2019;24:238–245.
42. Moussa MS, Hooijmans CM, Lubberding HJ, Gijzen HJ, van Loosdrecht MC. Modelling nitrification, heterotrophic growth and predation in activated sludge. Water Res 2005;39:5080–5098.
43. Zhai S, Ji M, Zhao Y, Pavlostathis SG, Zhao Q. Effects of salinity and COD/N on denitrification and bacterial community in dicyclic-type electrode based biofilm reactor. Chemosphere 2018;192:328–336.
44. Moussa MS, Sumanasekera DU, Ibrahim SH, et al. Long term effects of salt on activity, population structure and floc characteristics in enriched bacterial cultures of nitrifiers. Water Res 2006;40:1377–1388.
45. Jang D, Hwang Y, Shin H, Lee W. Effects of salinity on the characteristics of biomass and membrane fouling in membrane bioreactors. Bioresour Technol 2013;141:50–56.
46. Vo HNP, Ngo HH, Guo W, et al. Identification of the pollutants’ removal and mechanism by microalgae in saline wastewater. Bioresour Technol 2019;275:44–52.
47. Wang Z, Gao M, Wang Z, et al. Effect of salinity on extracellular polymeric substances of activated sludge from an anoxic–aerobic sequencing batch reactor. Chemosphere 2013;93:2789–2795.
48. Zhao Y, Park HD, Park JH, et al. Effect of different salinity adaptation on the performance and microbial community in a sequencing batch reactor. Bioresour Technol 2016;216:808–816.
49. Lefebvre O, Habouzit F, Bru V, Delgenes JP, Godon JJ, Moletta R. Treatment of hypersaline industrial wastewater by a microbial consortium in a sequencing batch reactor. Environ Technol 2004;25:543–553.
50. Dinçer AR, Kargi F. Performance of rotating biological disc system treating saline wastewater. Process Biochem 2001;36:901–906.
51. Frank WB, Regnery J, Chan KE, Ramey DF, Spear JR, Cath TY. Co-treatment of residential and oil and gas production wastewater with a hybrid sequencing batch reactor-membrane bioreactor process. J Water Process Eng 2017;17:82–94.
52. Di Bella G, Di Trapani D, Freni G, Torregrossa M, Viviani G. Analysis of biomass characteristics in MBR and MB-MBR systems fed with synthetic wastewater: Influence of a gradual salinity increase. Chem Eng Trans 2014;38:445–450.
53. Wan C, Yang X, Lee D-J, Liu X, Sun S, Chen C. Partial nitrification of wastewaters with high NaCl concentrations by aerobic granules in continuous-flow reactor. Bioresour Technol 2014;152:1–6.
54. Ramaswami S, Uddin FMJ, Behrendt J, Otterpohl R. High-rate nitrification of saline wastewaters using fixed-bed reactors. J Environ Manag 2019;243:444–452.
55. Rene ER, Kim SJ, Park HS. Effect of COD/N ratio and salinity on the performance of sequencing batch reactors. Bioresour Technol 2008;99:839–846.
56. Wang Z, Gao M, Wei J, et al. Long-term effects of salinity on extracellular polymeric substances, microbial activity and microbial community from biofilm and suspended sludge in an anoxic-aerobic sequencing batch biofilm reactor. J Taiwan Inst Chem Eng 2016;68:275–280.
57. Ghafari S, Hasan M, Aroua MK. Improvement of autohydrogenotrophic nitrite reduction rate through optimization of pH and sodium bicarbonate dose in batch experiments. J Biosci Bioeng 2009;107:275–280.
58. She Z, Wu L, Wang Q, et al. Salinity effect on simultaneous nitrification and denitrification, microbial characteristics in a hybrid sequencing batch biofilm reactor. Bioprocess Biosyst Eng 2018;41:65–75.
59. Uygur A, Kargi F. Salt inhibition on biological nutrient removal from saline wastewater in a sequencing batch reactor. Enzyme Microb Technol 2004;34:313–318.
60. Giustinianovich EA, Campos JL, Roeckel MD, Estrada AJ, Mosquera-Corral A, Val del Río Á. Influence of biomass acclimation on the performance of a partial nitritation-anammox reactor treating industrial saline effluents. Chemosphere 2018;194:131–138.
61. Li J, Ye W, Wei D, et al. System performance and microbial community succession in a partial nitrification biofilm reactor in response to salinity stress. Bioresour Technol 2018;270:512–518.
62. Ji J, Peng Y, Wang B, et al. Effects of salinity build-up on the performance and microbial community of partial-denitrification granular sludge with high nitrite accumulation. Chemosphere 2018;209:53–60.
63. Ge CH, Dong Y, Li H, et al. Nitritation-anammox process – a realizable and satisfactory way to remove nitrogen from high saline wastewater. Bioresour Technol 2019;275:86–93.
64. Kim LH, Chong TH. Physiological responses of salinity-Stressed Vibrio sp. and the effect on the biofilm formation on a nanofiltration membrane. Environ Sci Technol 2017;51:1249–1258.
65. Kinyage JPH, Pedersen PB, Pedersen L-F. Effects of abrupt salinity increase on nitrification processes in a freshwater moving bed biofilter. Aquac Eng 2019;84:91–98.
66. Wu D, Li GF, Shi ZJ, et al. Co-inhibition of salinity and Ni(II) in the anammox-UASB reactor. Sci Total Environ 2019;669:70–82.
67. Tang CJ, Zheng P, Wang CH, et al. Performance of high-loaded ANAMMOX UASB reactors containing granular sludge. Water Res 2011;45:135–144.
68. Ma C, Jin RC, Yang GF, Yu JJ, Xing BS, Zhang QQ. Impacts of transient salinity shock loads on anammox process performance. Bioresour Technol 2012;112:124–130.
69. Sheng GP, Yu HQ, Li XY. Extracellular polymeric substances (EPS) of microbial aggregates in biological wastewater treatment systems: A review. Biotechnol Adv 2010;28:882–894.
70. Vyrides I, Stuckey DC. Adaptation of anaerobic biomass to saline conditions: role of compatible solutes and extracellular polysaccharides. Enzym Microb Technol 2009;44:46–51.
71. Alias MA, Muda K, Affam AC, Aris A, Hashim N. The effect of divalent and trivalent cations on aggregation and surface hydrophobicity of selected microorganism. Environ Eng Res 2017;22:61–74.
72. Tsuneda S, Jung J, Hayashi H, Aikawa H, Hirata A, Sasaki H. Influence of extracellular polymers on electrokinetic properties of heterotrophic bacterial cells examined by soft particle electrophoresis theory. Colloids Surf B Biointerf 2003;29:181–188.
73. Mesdaghinia A, Ghahremani MH, Nabizadeh R, Nasseri S, Rafiee M. Role of CODPCP/CODTotal ratio on p-chlorophenol toxicity towards aerobic granular sludge. J Ind Eng Chem 2017;54:440–446.
74. Fang F, Yang M-M, Wang H, Yan P, Chen Y-P, Guo J-S. Effect of high salinity in wastewater on surface properties of anammox granular sludge. Chemosphere 2018;210:368–375.
75. Guo X, Miao Y, Wu B, et al. Correlation between microbial community structure and biofouling as determined by analysis of microbial community dynamics. Bioresour Technol 2015;197:99–105.
76. Kim HG, Kim SS, Kim SC, Joo HJ. Effects of Ca2+ on biological nitrogen removal in reverse osmosis concentrate and adsorption treatment. J Ind Eng Chem 2018;57:216–225.
77. Zhang L, Feng X, Zhu N, Chen J. Role of extracellular protein in the formation and stability of aerobic granules. Enzym Microb Technol 2007;41:551–557.
78. Ou D, Li W, Li H, et al. Enhancement of the removal and settling performance for aerobic granular sludge under hypersaline stress. Chemosphere 2018;212:400–407.
79. Hou M, Li W, Li H, Li C, Wu X, Liu YD. Performance and bacterial characteristics of aerobic granular sludge in response to alternating salinity. Int Biodeterior Biodegradation 2019;142:211–217.
80. Wu X, Li W, Ou D, et al. Enhanced adsorption of Zn2+ by salinity-aided aerobic granular sludge: Performance and binding mechanism. J Environ Manag 2019;242:266–271.
81. Corsino SF, Capodici M, Pippo FD, Tandoi V, Torregrossa M. Comparison between kinetics of autochthonous marine bacteria in activated sludge and granular sludge systems at different salinity and SRTs. Water Res 2019;148:425–437.
82. Huang JL, Wang HH, Alam F, Cui YW. Granulation of halophilic sludge inoculated with estuarine sediments for saline wastewater treatment. Sci Total Environ 2019;682:532–540.
83. Corsino SF, Campo R, Bella GD, Torregrossa M, Viviani G. Cultivaotin of granular sludge with hypersaline oily wastewater. Int Biodeterior Biodegradation 2015;105:192–202.
84. Li X, Luo J, Guo G, Mackey HR, Hao T, Chen G. Seawater-based wastewater accelerates development of aerobic granular sludge: A laboratory proof-of-concept. Water Res 2017;115:210–219.
85. Park SJ, Lee SH. A study on the biological treatment of acid pickling wastewater containing a high concentration of nitrate nitrogen. J Korean Soc Water Environ 2015;31:253–261.
86. Su KZ, Ni BJ, Yu HQ. Modeling and optimization of granulation process of activated sludge in sequencing batch reactors. Biotechnol Bioeng 2013;110:1312–1322.
87. Szabó E, Hermansson M, Modin O, Persson F, Wilén BM. Effects of wash-out dynamics on nitrifying bacteria in aerobic granular sludge during start-up at gradually decreased settling time. Water 2016;8:172.
88. de Sousa Rollemberg SL, Barros ARM, Firmino PIM, dos Santos AB. Aerobic granular sludge: Cultivation parameters and removal mechanisms. Bioresour Technol 2018;270:678–688.
89. Chen Y, He H, Liu H, et al. Effect of salinity on removal performance and activated sludge characteristics in sequencing batch reactors. Bioresour Technol 2018;249:890–899.
90. Zhang Y, Jiang W-L, Xu R-X, Wang G-X, Xie B. Effect of short-term salinity shock on unacclimated activated sludge with pressurized aeration in a sequencing batch reactor. Separ Purif Technol 2017;178:200–206.
91. Vargas C, Nieto JJ. Genetic tools for the manipulation of moderately halophilic bacteria of the family halomonadaceae. Methods Mol Biol 2004;267:183–208.
92. Romano I, Lama L, Nicolaus B, Poli A, Gambacorta A, Giordano A. Halomonas alkaliphila sp. nov., a novel halotolerant alkaliphilic bacterium isolated from a salt pool in Campania (Italy). J Gen Appl Microbiol 2006;52:339–348.

Article information Continued

Fig. 1

Schematic diagram of lab. scale reactor.

Fig. 2

Results of COD concentration with salinity injection.

Fig. 3

Results of nitrogen compounds concentration with salinity injection.

Fig. 4

Results of SNR and SDNR value with salinity injection.

Fig. 5

Results of PN, PS and PS/PN ratio value with salinity injection.

Fig. 6

Results of microbial communities using dynamic pie chart (Krona). (a) Initial phase AGS and (b) End phase AGS.

Table 1

Characteristics of Salinity Wastewater (unit: mg/L)

Mode (Salinity) Cl Na+ SO42− Mg2+ Ca2+ K+
1 (0.5 wt.%) 2,783.3 1,516.7 395.0 200.0 66.7 66.7
2 (1.0 wt.%) 5,566.7 3,033.3 790.0 400.0 133.3 133.3
3 (1.5 wt.%) 8,350.0 4,550.0 1,185.0 600.0 200.0 200.0
4 (2.0 wt.%) 11,133.3 6,066.7 1,580.0 800.0 266.7 266.7
5 (2.5 wt.%) 13,916.7 7,583.3 1,975.0 1,000.0 333.3 333.3
6 (3.0 wt.%) 16,700.0 9,100.0 2,370.0 1,200.0 400.0 400.0

Table 2

Experimental Conditions of Lab. Scale Reactor

Vol. (L) Flow (L/day) Cycles/day pH HRT (h) SRT (d) Temp. (°C)
5 7.5 3 7.0–7.5 16 20–25 25 ± 2
1 cycle time (min): feeding(10)→aeration(270)→anoxic(150)→settlling(10)→decanting(10)→idle(30)